Development and research of technology for obtaining and properties of welding wire from Al-Mg-Sc alloys using combined methods of thermal deformation treatment : научное издание

Sidelnikov Sergey Borisovich; Voroshilov Denis Sergeevich; Lopatina Ekaterina Sergeevna; Yakivyuk Olga Viktorovna; Konstantinov Igor Lazarevich; Mansurov Yulbarskhon Nabievich; Orelkina Tamara Aleksandrovna; Galiev Roman Ilsurovich; Ber Vladimir Ivanovich; Belokonova Irina Nikolaevna; Durnopyanov Alexander Vasilyevich

Дополнительные ссылки: eLibrary

База данных: Каталог библиотеки СФУ

Библиографическое описание: Development and research of technology for obtaining and properties of welding wire from Al-Mg-Sc alloys using combined methods of thermal deformation treatment : научное издание / S. B. Sidelnikov [et al.]. - Текст : непосредственный // International Journal of Lightweight Materials and Manufacture. - 2024. - Т.7, №3. - P. 384-404. - ISSN 2588-8404, DOI 10.1016/j.ijlmm.2024.02.001.

Аннотация: The results of studies technological processes for obtaining welding wire from alloys of the Al-Mg system with a scandium content of 0.12 (alloy 1580) and 0.25 wt % (alloy 01570) presented. A feature of the technology is the production of a billet for further cold deformation by an energy-efficient method of ingotless rolling-extrusion (IRE). It was found that hot-extruded rods from the investigated alloys obtained by the IRE method have the required level of plastic and strength properties necessary for further cold deformation up to 80%. Thermomechanical processing of hot-extruded rods manufactured by IRE have been developed and experimentally tested, which made it possible to obtain a billet with a square side of 5 x 5 mm by sectional rolling and wire with a diameter of 3 mm by drawing. Studies of the structure and mechanical properties of deformed semi-finished products have shown that the developed modes make it possible to obtain a welding wire from the investigated alloys that meets the requirements of current standards. Studies of the operational properties of the obtained welding wire were carried out. It was found that alloy 1580 with a minimum content of scandium (0.12 wt %) is not inferior to alloy 01570 in terms of corrosion resistance and weld quality. Developed technology for the production of welding wire from alloys of the AleMg system with different scandium content can be recommended for industrial use. It is advisable to implement alloy 1580, which has a lower cost compared to alloy 01570.

Год издания: 2024

Авторы: Sidelnikov Sergey Borisovich , Voroshilov Denis Sergeevich , Lopatina Ekaterina Sergeevna , Yakivyuk Olga Viktorovna , Konstantinov Igor Lazarevich , Mansurov Yulbarskhon Nabievich , Orelkina Tamara Aleksandrovna , Galiev Roman Ilsurovich , Ber Vladimir Ivanovich , Belokonova Irina Nikolaevna , Durnopyanov Alexander Vasilyevich

Издательство: KeAi Publishing Communications Ltd.

Источник: International Journal of Lightweight Materials and Manufacture

Выпуск: Т.7, №3

Номера страниц: 384-404

Держатель оригинала документа: Huanggang Normal University, Siberian Federal University, Tashkent State Transport Universit

Количество экземпляров:

Твёрдая копия издания отсутствует в фонде библиотеки

Показать дополнительные сведения

Modeling and investigation of combined processes of casting, rolling, and extrusion to produce… : научное издание

Sidelnikov Sergey Borisovich и др.
2024 год

Infuence of the Parameters of Combined Processing and Drawing on the Structure and Properties of… : научное издание

Bespalov V.M. и др.
2023 год

Evaluation the influence of combined thermal-deformation treatment parameters on the physical and… : научное издание

Bespalov Vadim Mikhaylovich и др.
2025 год

Investigation of structure and properties of the welded joint obtained by friction stir welding of… : научное издание

Konstantinov I. L. и др.
2024 год

Combined rolling‑extrusion of various billets from the Al–Ce–La alloy for electrical wire production : научное издание

Voroshilov Denis Sergeevich и др.
2024 год

Investigation the structure and properties of deformed semi-finished products produced from chips… : статья из журнала

Sidelnikov S.B. и др.
2023 год

Obtaining Al–Zr-Hf wire using electromagnetic casting, combined rolling-extrusion, and drawing : статья из журнала

Voroshilov D.S. и др.
2022 год

Combined rolling-extrusion of rods from alloy Al-0.5REM using billet after electromagnetic mold : научное издание

Voroshilov Denis и др.
2023 год

Mechanical properties and microstructure of multi-pass butt weld of plates made of Al-Mg-Zr alloy… : научное издание

Dovzhenko N.N. и др.
2021 год

Characterization properties and structure for wires from Al-Ce-La system alloy via the method of… : научное издание

Voroshilov Denis S.
2025 год

Investigation of various process attributes in an ingotless rolling-extrusion process imposed on… : научное издание

Sidelnikov Sergey Borisovich и др.
2024 год

Application of Methods Combined Treatment for Obtaining Welding Wire from Silumins : статья из журнала

Sokolov Ruslan E. и др.
2015 год

Influence of stepped annealing on the properties of conductor wire after ingotless rolling… : научное издание

Bespalov Vadim и др.
2023 год

Investigation structure and properties of wire from the alloy of AL-REM system obtained with the… : научное издание

Sidelnikov S.B. и др.
2021 год

Modeling and study of the technology for obtaining solder wire from new silver-based alloys… : статья из журнала

Sidelnikov S.B. и др.
2022 год

The Influence of Production Technology and Subsequent Deformation Treatment on the Microstructure… : научное издание

Medvedev A. E. и др.
2026 год

Библиотечно-издательский комплекс СФУ

Development and research of technology for obtaining and properties of welding wire from Al-Mg-Sc alloys using combined methods of thermal deformation treatment : научное издание
статья из журнала

Похожие публикации